Thursday, 3 September 2009
Different radiators in the bathroom
Before choosing your radiator, you must determine how much heat the bathroom requires. This is done by using the radiator manufacturer’s heat loss calculations (your radiator installer can do this when quoting). The most accurate calculations take room measurements, including the window and outside wall sizes. They calculate the temperature required and apply this to determine the radiator size. Too big and the system will exceed its temperature requirement and be uneconomical to run, too small and it won't reach its desired temperature.
Heated towel rails are an alternative to common radiators as they provide a rail for hanging towels, act as radiators and possess a popular, modern style. There are many different designs and styles of heated towel rail but the most popular are the ladder type, which are usually available in a white or chrome finish. Choosing the right model needs some consideration.
Heated towel rails are designed to be plumbed in to your central heating system in the same way as a radiator, but there are two other installation options.
Dual Fuel Option - the towel rail can be installed with an electrical heating element that fits inside one of the vertical rails. Special radiator valves are used which enable the radiator to be isolated from the heating system and warmed using the electric element. This is very useful in summer months when your heating may be off.
Oil Filled Option - with this option the towel rail is not connected to your heating system, and is heated by electricity alone. The towel rail is factory fitted with a heating element and filled with special oil, ready for connection to your electricity supply.
All radiators have different heat outputs depending on the size and design. Make sure that you are replacing a radiator with a heated towel rail of similar output; otherwise you might notice a drop in temperature in the bathroom.
Electric radiators are an option if you do not wish to install a standard, centrally heated type. Conventional radiators need to be attached to the existing system, and this may be a hassle that electric radiators avoid. Many new electric models claim to save energy in the long term; this becoming a popular feature for money and energy saving people. They also possess a timer which can be set to turn on or off at particular times to suit the user. Although electric radiators are generally more bulky than their counterparts, there are an increasing number to choose from, allowing the buyer a wide selection choice.
Monday, 20 July 2009
The benefits of a low-flow toilet
One of the most obvious benefits of low-flow toilets is the fact that they conserve water. The average person flushes the toilet six times each day. Low-flow toilets use approximately 172 litres less water per day than other toilets. This creates massive water conservation. Using less water is also beneficial to consumers as it saves money. Due to the fact that low-flow toilets use a smaller amount of water than other toilets, their tanks don't need to be as large. This makes the toilet smaller, and thus generally more attractive.
The environmental and economical benefits are a big plus; however it must be considered that toilets have been reduced in size and thus struggle to remove as much waste as older toilets.
If the benefits of a low-flow toilet outweigh the drawbacks to the consumer, then they are a perfectly worthwhile purchase. Almost all new toilets are low-flow varieties anyway. The money you spend to purchase the toilet can be regained in a few years by the amount of money you save using less water.
Another option for a suitable toilet is the dual flush design. This refers to the two buttons that are used to operate the toilet. Pressing one button will flush the toilet with about 3 litres of water and is generally referred to as a short flush. Pressing the other button will release about 6 to7 litres of water and is called a long flush.
Despite the use of the words "short" and "long," the long flush of a dual flush toilet generally uses less than half of the water that is needed in a normal toilet, which by and large uses around 20 litres of water per flush. The dual flush is so efficient that it is arguably the most efficient toilet on the market.What's more, you will be playing your part in saving resources.
If you have decided and are ready to purchase a low-flow or dual flush toilet, make certain to do your homework and compare brands and types. Some do a better job of disposing of waste than others, and research by experts can inform you of toilets that are good quality and best buys.
More tips and advice for replacing a toilet, replacing a bath or replacing and descaling a shower head can be found at lets-do-diy.com
Friday, 3 July 2009
Tips and advice when tiling
Newly plastered walls should always be treated with a polyvinyl acetate (PVA) sealant solution - five parts water to one part PVA. This will seal the surface and promote adhesion.
To determine the number of tiles you will need, calculate the surface area of the wall by multiplying the length of the wall by its height (or by the height you wish to tile up to). This should be done for each surface you are planning to tile; then the figures for each surface should be added together. Always add at least 10% to your final figure to allow for wastage and cutting, and then divide the total surface area by the area of one tile.
Tiling adhesive is available as a dry powder that you mix with water or in ready-mix tubs, which can be used as both adhesive and grouting. Remember that some surfaces may require a particular adhesive e.g. shower cubicles, so ask at your local DIY store if you are not sure.
Remember not to lay the adhesive more than 4mm thick. Apply the adhesive evenly over the surface, but avoid covering too large an area as it may dry before you fit the tiles.
Finally, when grouting, make sure the adhesive has been given enough time to go hard (ideally 12 hours). Also check that there is nothing protruding above the surface of the tile that will get in the way of the grout. Finish off by using a grout shaper to create a smooth finish.
More tips and advice for fixing ceramic wall tiles, fixing mosaic tiles to a wall or replacing a damaged tile can be found at lets-do-diy.com
An easy way to saving energy and water
Using a low-flow shower head can cut the total water usage to less than ten gallons saving thousands of gallons of water per year. Depending on your showerhead and whether it has a flow restrictor in it and how long you shower, the answer could oscillate either towards shower or bath.
There are two types of low-flow shower heads: aerating and non-aerating.
Aerating - mixes air into the water stream. This maintains steady pressure so the flow has an even, full shower spray. Because air is mixed in with the water, the water temperature can cool down a bit towards the floor of the shower. Aerating shower heads are the most popular type of low-flow shower head.
Non-aerating - air is not mixed into the water stream. This maintains temperature well and delivers a strong spray. The water flow pulses with non-aerating shower heads, giving more of a massaging showerhead effect.
More tips and advice for fitting a bathroom sink, installing a shower or wiring an electric shower can be found at lets-do-diy.com
Monday, 11 May 2009
Greener UK
Research from the price comparison site reveals that more than three-quarters (78 per cent) of UK households are more energy efficient now than they were 12 months ago.
Of such people, 36 per cent cite recent increases in the cost of gas and electricity.
Ann Robinson, director of consumer policy for uSwitch.com, states: "Consumers are reacting to the recession and the high cost of energy by cutting back on energy usage."
The study also reveals that 43 per cent of people believe that taking the time to reduce energy usage will cost them, with 64 per cent of consumers yet to have cavity or solid wall insulation installed in the home citing the expense involved in such a project as a reason why they do not.
However, by carrying out energy efficient DIY work, homeowners may find that any initial expenditure is recouped later on through lower utility bills.
Last month, Grand Designs present Kevin McCloud claimed eco-friendly DIY will play a crucial role in reducing the nation's carbon footprint.
Monday, 30 March 2009
Economy
I need to sit tight and wait. I have heard that many people in my old job have been let go, so I don’t have any regrets now. I least I have managed to get myself established in the handyman business. I think If had been made redundant now I would have panicked more than I am now. At least I know I am capable.
Tuesday, 3 March 2009
DIY Websites
I’m looking on the bright side, spring is on its way and I am completing jobs to a good standard. People are happy, and I am confident people will call me back for more work.
I am looking for good resources to get advice and tips to help me. There are a few good sites out there; Screwfix has a good forum, so does lets-do-diy, diynot and a few others. I am going to register to the lot and try them out to see who can help me best. I will keep you posted on my experience. I might end up a regular at all of them, but I predict I will settle for one or two of these sites.